Then you get to route the window defroster wire through the soft top sleeve and stuff but that's way too hard to explain without pics.Run the seatbelt through the new plastic trim, install the reused plastic plugs into the trim and snap it into place.Mine came with 2 sets of bolts for the bottom hole, it didn't seem to matter which I used but I thought that was weird. Ive installing all hardwares, include 2 front brackets, side mouldings with tracks from OEM soft top, red leather headliner with thick, firm insulation. I’ve also learned there are precut or aftermarket hardtop brackets available, but they appear to be so expensive that selling the soft top to get those may not be worth it. Install the mounting posts using the supplied bolts. I’ve learned I’ll need to cut my soft top connecting hardware to keep them as connecting points for the hardtop.The HT should have come with 2 new trim parts with sections of them cut out to accommodate the hard top mounting posts. Remove the left and right plastic trim parts that the seat belt passes through (unbolt the seatbelt base).Replace them with the stainless latch parts.Remove the rear tabs near the engine hinge that are body colored painted on the Left and Right side.but if no one posts up I can send you a scan of the install info via PM on Sunday. I believe that Gahh owns a couple of the popular brands such as Robbins, Sierra and EZ Top. It was a few years ago so I don't remember the actual instructions. SpyderChat Forum is a community for Toyota MR2 Spyder Enthusiasts to discuss specs, reliability and more Show Less. Those things above aren't in any instructions but two things I noticed I messed up on the first hard top install. 500 quid is NZD 951.51 Throw in 350 for sea freight and its a cheap hardtop Good Luck. I've updated the list based on responses in this thread and PM.Did it come with all mounting hardware and modified plastic trim pieces?Ģ things on that - when you pull the seatbelts through the old trim pieces, be careful not to pop the retaining rivet off of the seatbelt when you pull it through the plastic trim that is being replaced.Īlso, when installing the new plastic trim using the plastic rivet(s) that holds it in place, do not push too hard otherwise you will 'crease' the trim and create a white mark from pushing to hard (like when you fold a credit card in half, you get that white stress line from bending plastic). Spyder Hardtop Heres a Spyder Hardtop for sale in the uk. On this end the re-distribution will probably be by USPS Priority Mail flat-rate box shipping, unless a number of buyers all happen to be in the same area. There are no leaks and the headliner is excellent. Overall the hardtop is in good condition. This roof was removed from a 2003 spec car with paint code 1E7 Crystal Silver. Direct from the UK to your door in the USA. Ive tried pushing down on it but it seems like the thickness of the. Toyota MR2 Spyder/Roadster Hardtop and complete fitting kit in original factory silver paint. When I test fit the new hard top on the car it will not sit flush against the weather seal at the front where the windshield is at. If warranted, I may start a separate group buy thread. Hi, I have an 01 MR2 Spyder and Im in the process of installing an aftermarket hardtop. Just unbolt the rear endlinks and rear brackets and rotate the bar a bit as you slide it out. and the Whiteline was a bit heavier at 6.2 lbs. If hanging it as in the picture, make sure whatever bracket you use is drilled into stud as spreaders in the sheetrock wont cut it. I'll PM some of the others who've indicated an interest in this, in case they are not actively following this thread. The Whiteline rear bar is 18mm and 5 way adjustable. Toyota MR2 Spyder MR-S Hardtop Strikers Side Fittings Interior Mounting Brackets. Add an aggressive and unique style to your convertible with a custom hardtop from VIS Racing. 2000 - 2005 Toyota MR2 OEM Style Carbon Fiber Hardtop. To begin, can you give us pricing on these items, assuming a quantity of five sets, and with combined shipping added? On this side I'll start a list of buyers, with me and Celicajonz as the first two confirmed: 2000 - 2005 Toyota MR2 OEM Style Fiberglass Hardtop - VIS Racing. Having started this, I should volunteer to organize it. Hi Patrick, I made the contact with Dick Sloan about arranging a potential group buy.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |